ADU · Delaware County
Can you build an ADU in Sidney, NY?
Village of Sidney has 6 districts. All districts prohibit ADUs. Check your address to confirm the district that applies to your parcel:
What the Sidney code indicates by district
The table below shows how each district treats ADUs, alongside the lot and setback standards that govern a second unit. District boundaries and conditions vary, so treat this as a starting point and confirm the district that applies to your parcel.
| District | Min lot | Setbacks F / S / R | Max height | ADU |
|---|---|---|---|---|
| R-1 Residential District — the Village's base single-family district, and the district whose standards every other residential district in Sidney is written against. § 215-7E sets minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, maximum lot coverage 30% and maximum building height 35 feet OR 2 1/2 STORIES, whichever binds first — the storey cap is a genuine second constraint and a low-pitch three-storey design can fail it while still under 35 feet. The 30% is a GENUINE MAXIMUM LOT COVERAGE, stated in those words in § 215-7E(3); it is NOT an inverse minimum-green-space or open-space standard, so it needs no reinterpretation. YARDS: front 35 feet, side 4 feet, rear NOT LESS THAN THE HEIGHT OF THE PRINCIPAL BUILDING. A single-storey 18-foot house needs an 18-foot rear yard; a full 35-foot house needs 35 feet. SIDE YARD HAS A SECOND LIMB THAT OFTEN BINDS HARDER THAN THE 4 FEET: § 215-7E(5)(b) reads 'four feet, but not less than 12 feet from an existing building on an adjacent lot'. The 4 feet is the lot-line measure and is what sideSetback records; the 12 feet is a BUILDING-SEPARATION rule measured to a neighbouring structure, so on a narrow lot with a close neighbour the buildable width shrinks well below what 4 feet suggests. Check what is standing next door before sizing a footprint. ACCESSORY BUILDINGS get their own relief — 3 feet from a side or rear lot line, but never within 12 feet of an existing dwelling. FRONT YARD EXCEPTION: the 35 feet does not apply where a subdivision plan with a lesser front yard was approved and filed with both the Village of Sidney and the Delaware County Clerk. CORNER LOTS ARE PENALISED: § 215-7E(6) treats any lot with two sides fronting a public street as a corner lot and requires EVERY street-facing yard to meet the full 35-foot front-yard standard, so a corner lot carries two 35-foot fronts rather than one front and one side. Permitted principal uses are single-family dwellings, family day care / group family day care, and customary agricultural uses — with farm animals and poultry barred from being pastured, stabled or housed within 100 feet of any property line. NO ADU: the accessory-use list is closed and contains none — see aduNotes. | 0.241 ac | 35 / 4 / - ft | 35 ft | No |
| R-1A Residential District — dimensionally identical to R-1 for ordinary lots, and the recorded figures are R-1's: § 215-8 states 'Area, height, density and yard requirements: same as R-1, except townhouse developments shall have the following minimum requirements'. So minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, coverage 30%, height 35 feet or 2 1/2 storeys, front 35 feet, side 4 feet with the same 12-foot building-separation limb, and a rear yard equal to the height of the principal building (null for the reason given in the R-1 label). For a townhouse development the requirement is a MINIMUM TOTAL DEVELOPMENT AREA OF 5,000 SQUARE FEET PER UNIT (0.1148 acres per unit), together with maximum lot coverage 30%, maximum height 35 feet or 2 1/2 storeys, front yard 35 feet, side yards 4 feet subject to the same 12-foot separation rule, and a rear yard equal to the height of the principal building. Read that correctly: the 10,500 square foot figure is the minimum for a conventional lot, while a townhouse scheme is sized off the 5,000 square feet PER UNIT figure applied to the whole development parcel — a 1.5-acre site supports about 13 townhouse units, not 6 lots. Sizing a townhouse project off the 10,500 minimum would understate it by roughly half, and sizing a conventional subdivision off the 5,000 figure would overstate it by the same margin. The corner-lot rule and the 3-foot accessory-building relief carry over from R-1 unchanged. NO ADU — see aduNotes; a townhouse unit here is a principal dwelling, not an accessory one. | 0.241 ac | 35 / 4 / - ft | 35 ft | No |
| R-2 Residential District — DIMENSIONALLY IDENTICAL TO R-1 IN EVERY COLUMN, and deliberately so: § 215-9E reads 'Area, height, density and yard requirements: (1) Same as R-1.' Minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, coverage 30%, height 35 feet or 2 1/2 storeys, front 35 feet, side 4 feet with the 12-foot building-separation limb, rear yard equal to the height of the principal building (null — see the R-1 label). The identical figures are real, not a transcription artefact; what separates R-2 from R-1 is USE, not bulk. There is NO per-unit density standard, no additional land requirement and no lot-area-per-dwelling-unit figure anywhere in § 215-9 — the second unit costs no extra land at all, which makes R-2 materially more productive per acre than R-1 despite sharing every dimensional number with it. R-2 also carries forward all R-1 permitted uses subject to their own restrictions. Additional special permit uses over R-1: professional offices, and bed-and-breakfasts subject to Planning Board review against the four character standards described in strNotes. Permitted accessory uses are 'Same as R-1' plus in-home New York State certified day-care facilities; prohibited uses are 'Same as R-1'. Off-street parking conforms to § 215-15, which should be checked for any two-family proposal. NO ADU: the second unit here is a two-family PRINCIPAL use, not an accessory dwelling unit — see aduNotes for why that distinction matters. | 0.241 ac | 35 / 4 / - ft | 35 ft | No |
| R-3 Residential District — the Village's multifamily district and the only residential district with its own dimensional standards rather than R-1's. § 215-10E: minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, maximum lot coverage 40%, maximum building height 40 FEET OR NOT MORE THAN THREE STORIES, front yard 20 feet. Coverage and height are both more generous than R-1's 30% and 35 feet, and the front yard is 15 feet shorter, so R-3 is the most permissive residential envelope in Sidney. The 10,500 square feet is the floor for the LOT, and once you hold a conforming lot the unit count is governed by the 1,000 square feet per dwelling unit figure — so a bare-minimum 10,500 square foot lot could in principle carry TEN units, and a half-acre lot about twenty-one, subject to the 40% coverage cap, the 40-foot/three-storey height limit, the yards and off-street parking, which will realistically bind first. Do not size an R-3 multifamily scheme off the 10,500 figure; do not assume the 1,000 square feet per unit is achievable without checking coverage, height and parking together. BOTH SIDE AND REAR YARDS ARE HEIGHT-DEPENDENT AND ARE RECORDED null FOR THAT REASON: § 215-10E(5) sets the side yard at 'not less than 1/3 of the height of the principal building' and the rear yard at 'not less than the height of the principal building'. On a full 40-foot building that is a 13.3-foot side yard and a 40-foot rear yard; on a 25-foot building it is 8.3 and 25. Because both scale with the building actually proposed, no single figure is honest and the rule is carried here instead. NOTE THE SIDE-YARD BASIS CHANGES BETWEEN DISTRICTS — R-1, R-1A and R-2 use a flat 4 feet, R-3 uses one-third of building height, so an R-3 side yard is larger than an R-1 side yard for anything above 12 feet tall. Accessory-building relief is 'same as R-1' (3 feet from side or rear lot line, never within 12 feet of an existing dwelling). Principal uses: all R-2 uses plus multiple-family dwellings. Special permit uses add clubhouses, golf and country clubs, tennis clubs and other not-for-profit recreational facilities, establishments for cultural and social purposes run by not-for-profit membership corporations, and MOBILE HOME PARKS. NO ADU — see aduNotes. | 0.241 ac | 20 / - / - ft | 40 ft | No |
| B-1 Commercial District — a TWO-REGIME district, and reading the wrong regime is the trap here. § 215-11D splits the standards: '(1) Residential lots: same as R-3 Residential District requirements. (2) Nonresidential lots: no requirements, except: (a) Side and rear yard requirements of R-3 Residential Districts shall be applicable to side or rear yards when adjacent to an existing residential lot or district. (b) Maximum building height: 50 feet.' So minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, coverage 40%, front yard 20 feet, and side and rear yards that are height-dependent under R-3's one-third-of-height and full-height rules (recorded null for the reason given in the R-3 label). maxHeight is recorded as 40 feet, R-3's figure, NOT the 50 feet in § 215-11D(2)(b) — THE 50-FOOT CAP APPLIES TO NONRESIDENTIAL LOTS ONLY, and recording it on a row whose every other number is residential would silently mix the two regimes and let a user stack a 50-foot height onto R-3 lot and yard standards that were never written to carry it. A NONRESIDENTIAL BUILDING IN B-1 IS SUBJECT TO ALMOST NOTHING: no minimum lot area, no lot width, no coverage limit and no front yard, with side and rear yards required only where the lot abuts an existing residential lot or district, and a 50-foot height cap. If you are underwriting a commercial building here, ignore every figure on this row except that 50 feet and the conditional side/rear yards. B-1 permits everything permitted in R-3, subject to its restrictions, plus stores and shops for any retail business including personal service shops. Because R-3 uses come through in full, MULTIPLE-FAMILY DWELLINGS ARE PERMITTED IN B-1 AT R-3'S 1,000 SQUARE FEET PER DWELLING UNIT — B-1 is a genuine multifamily site, not merely a commercial strip. Off-street parking conforms to § 215-15. NO ADU — see aduNotes. | 0.241 ac | 20 / - / - ft | 40 ft | No |
| B-2 Commercial District — structurally the same two-regime district as B-1, with one difference in the height rule. § 215-13D: '(1) Residential lots: same as R-3 Residential District requirements. (2) Nonresidential lots: no area, density or yard requirements, except that side and rear yard requirements of R-3 Residential Districts shall be applicable to side or rear yards when adjacent to an existing residential lot or district. No building shall be more than 50 feet in height unless the Planning Board determines that special conditions necessitate a greater height.' AS IN B-1, THE RECORDED FIGURES ARE THE RESIDENTIAL REGIME: minimum lot area 10,500 square feet (0.241 acres), minimum lot width 70 feet, coverage 40%, front yard 20 feet, height 40 feet (R-3's figure), and height-dependent side and rear yards recorded null under R-3's one-third-of-height and full-height rules. B-2 is therefore the only district in the Village of Sidney with no hard ceiling on building height, subject to a discretionary Planning Board finding. That relief is written into the NONRESIDENTIAL limb, so whether it reaches a residential building on a residential lot in B-2 is genuinely unclear from the text and should be confirmed with the Village before it is relied on. The nonresidential regime is again near-unregulated — no area, no density, no yards except where abutting residential. R-3 uses come through, so multifamily at 1,000 square feet per dwelling unit is available here as in B-1. Off-street parking conforms to § 215-15. NO ADU — see aduNotes. | 0.241 ac | 20 / - / - ft | 40 ft | No |
ADUs vs. short-term rentals in Sidney
No local short-term-rental law on record - which is not the same as permission for Village of Sidney. NO short-term-rental regime exists in the Village of Sidney. The full Village Code chapter list was enumerated on 2026-08-20 (36 chapters, Ch. 1 General Provisions through Ch. 215 Zoning) and there is NO transient-rental, short-term-rental or tourist-accommodation chapter — contrast the TOWN of Walton in this same county, which has a standalone Chapter 192 Transient Rental Regulations. ABSENCE IS NOT PERMISSION, so this is recorded unknown rather than permitted. TWO THINGS CUT AGAINST A PERMISSIVE READING AND A BUYER UNDERWRITING STR INCOME MUST WEIGH BOTH. FIRST, § 215-7D IS A CLOSED-LIST CLAUSE: 'All uses not specifically listed as permitted shall be considered prohibited in the R-1 District.' SECOND, THE ONLY TRANSIENT-LODGING USE ANYWHERE IN THE RESIDENTIAL DISTRICTS IS A BED-AND-BREAKFAST, AND IT IS A SPECIAL PERMIT USE, NOT AS OF RIGHT — § 215-9B(3) makes bed-and-breakfasts subject to Planning Board review and approval against four named standards (exterior changes must retain the residential character of the premises and the neighborhood; the parking area must not unduly change the outside character; any exterior signage must be unilluminated and not detract from residential character; and outdoor congregation areas such as walking areas, swimming pools and barbecue areas must be properly maintained and in character with the neighborhood). A Village that requires a special permit for a bed-and-breakfast is unlikely to treat an unpermitted whole-house short-term rental as an allowed use, but the code does not say so in terms. WHAT DOES EXIST AND WILL APPLY REGARDLESS: Chapter 112 Housing Standards (§ 112-1 through § 112-73) and Chapter 150 Property Maintenance (§ 150-1 through § 150-16). Neither is an STR law and neither confers zoning permission. 112 and Ch. 150, either of which may carry rental-registration or inspection duties. Confirm current STR status with the Village Code Enforcement Officer before relying on this. These are separate questions from whether you can build an ADU — a unit you're allowed to add isn't automatically one you're allowed to rent nightly, so check both.
Good to know
- Residential lot minimum0.241 ac — an ADU still has to fit the district's lot and setback envelope.
- Last reviewed2026-08-20
ADU FAQ — Sidney, NY
Are ADUs allowed in Sidney, NY?
Village of Sidney has 6 districts. All districts prohibit ADUs. Check your address with the free ADU checker, or confirm with the building department.
Do I need a special permit for an ADU in Sidney?
No. No district in Village of Sidney permits an ADU, so there is no permit to apply for. Codes change, so verify with the building department before ruling it out.
Can I use an ADU as a short-term rental in Sidney?
No local short-term-rental law on record - which is not the same as permission for Village of Sidney. ADU occupancy and short-term-rental rules are separate: an ADU you can build isn't automatically one you can rent nightly. Confirm both before you count on STR income.
What an ADU costs to build in Sidney
Permission is one question and budget is another. An 800 sq ft accessory unit here runs roughly $185k–245k at a standard finish, and the per-square-foot rate comes in above a full house because the kitchen, bath, panel and heating plant cost the same either way. See the full cost to build an ADU in Sidney, priced by size.
More on Sidney: Full zoning for new construction · ADU build cost · House build cost · All Delaware County towns
ADU information for Village of Sidney is compiled from the municipal code (last reviewed 2026-08-20) and provided for decision-support only — not legal or architectural advice. ADU eligibility, size, owner-occupancy and permit conditions vary by district and often carry exceptions; verify with the municipality before relying on any answer. Source: Offsite / Aldo zoning dataset, municipalData.js.